Plugin Summary

carlo-gavazzi-em21.lua

DOWNLOAD

Plugin provided summary

Carlo Gavazzi compatible devices.

Originally developed with a EM210-72D, but extended to support:

Notable downside of these devices are that you can get 0.01 kWh resolution on the display, but only 0.1 kWh via modbus.

Wiring

EG pinMeter pin
+Not connected
-Not connected
AB
BA

cs-instruments-va5xx.lua

DOWNLOAD

Plugin provided summary

CS Instruments - VA5xx

Should work with any VA5xx series device. Note: this device specifies 18-36V supply! While it appears functional at 12V, the "gas temperature" reading doesn't seem reliable, possibly related to the voltage.

Tested with a VA500, sw 1.31, produced 24-nov-2017

Wiring

EGExtension CableDUT
+REDConnector A, pin 1 (Documents spec 18-36V, works at 12V)
-BLACKConnector A, pin 3
AYELLOWConnector A, pin 2
BGREENConnector A, pin 4

dalian_taosonics.lua

DOWNLOAD

Plugin provided summary

Supports DaLian Taosonics Instrument Co, CAM-3000M / TUF2000 water flow devices

dent_powerscout3.lua

DOWNLOAD

Plugin provided summary

Plugin for DENT PowerScout 3+ Serial devices in Modbus/RTU mode.

Wiring

EG pinMeter pin
+Not connected
-S
A+
B-
ReMake Electric, 2014/2.

etactica_eb-es.lua

DOWNLOAD

Plugin provided summary

eTactica EB and ES, 3,6,9 and 12 channel current measurement devices.

While the plugin lists the full 12 channels as available variables, only the correct physical number of channels will ever produce data. For PowerBars, kwh and power factor variables will be only available if the PowerSyncNetwork is active and operational for that device.

etactica_em.lua

DOWNLOAD

Plugin provided summary

eTactica EM, three-phase, high accuracy submeter. Support up to 3000A per phase by varying models.

etactica_er-generic.lua

DOWNLOAD

Plugin provided summary

eTactica ER plugin. Supports the optical and wired pulse inputs, as well as various OBIS values from the IR interface. 0.0.0, the meter serial is always included, but up to 10 other variables can also be included. The preset list of variables is suitable for Kamstrup 351b electricity meters and Kampstrup MC water meters. Requires ER firmware 3.6 or greater.

etactica_resi-cg-em340.lua

DOWNLOAD

Plugin provided summary

Plugin to support Carlo Gavazzi EM340 Mbus meters connected via a RESI MBUS-MODBUS gateway. Remember, the RESI module must have it's configuration uploaded first. The RESI variable mapping is not optional

Required RESI variable mapping

PositionMbus VariableNamedata typeexponent
1 0 Energy32 bit ieee floating point
2 1 Reactive System32 bit ieee floating point-2
3 8 Current 132 bit ieee floating point
4 9 Current 232 bit ieee floating point
5 10 Current 332 bit ieee floating point
6 20 Power factor 132 bit ieee floating point3
7 21 Power factor 232 bit ieee floating point3
8 22 Power factor 332 bit ieee floating point3
9 26 Voltage 1-N32 bit ieee floating point
10 27 Voltage 2-N32 bit ieee floating point
11 28 Voltage 3-N32 bit ieee floating point
12 33 Frequency32 bit signed binary1
eTactica can provide a "user database" file for the RESI ModbusConfigurator that provides these values.

Modbus Wiring between EG and RESI Gateway

EGExtension CableDUT
+REDNot connected
-BLACKM-
AYELLOWA+
BGREENB-

etactica_resi-emh.lua

DOWNLOAD

Plugin provided summary

Plugin to support EMH DIZ-G Mbus meters connected via a RESI MBUS-MODBUS gateway. Remember, the RESI module must have it's configuration uploaded first. The RESI variable mapping is not optional

Required RESI variable mapping

PositionMbus VariableNamedata typeexponent
1 0 Energy Net32 bit ieee floating point
2 6 Power 132 bit ieee floating point
3 7 Power 232 bit ieee floating point
4 8 Power 332 bit ieee floating point
5 9 Voltage 1-N32 bit ieee floating point
6 10 Voltage 2-N32 bit ieee floating point
7 11 Voltage 3-N32 bit ieee floating point
8 15 Current 132 bit ieee floating point
9 16 Current 232 bit ieee floating point
10 17 Current 332 bit ieee floating point
11 23 Frequency32 bit ieee floating point3
12 26 Firmware verison32 bit signed binary
eTactica can provide a "user database" file for the RESI ModbusConfigurator that provides these values.

Modbus Wiring between EG and RESI Gateway

EGExtension CableDUT
+REDNot connected
-BLACKM-
AYELLOWA+
BGREENB-

frer.lua

DOWNLOAD

Plugin provided summary

eTactica Gateway plugin for Frer multifunction meters

ReMake Electric, 1/2014. All optional fields are filled. Supports the following devices: These _should_ work too.

Wiring

EGExtension CableDUT
+REDnot connected
-BLACKnot connected
AYELLOWA+
BGREENB-

gc5-sfar-1m-xx.lua

DOWNLOAD

Plugin provided summary

GC5 SFAR-1M expansion modules

At present this _only_ supports the 2DI2DO modules, but should be easily expanded to support more.

Tested with a 2DI2DO version 3.1

Wiring

EGExtension CableDUT
+REDNC
-BLACKGND
AYELLOWRS485+
BGREENRS485-

ime-ce4dmid01.lua

DOWNLOAD

Plugin provided summary

eTactica Gateway plugin for IME Conto D4 - Pt MID meters (only!)

Currently supports ONLY the following devices (specified by IME document PR115.pdf)

IME Meters do not provide a serial number

IME Meters do not provide firmware version numbers ReMake Electric, 2/2014.

janitza_umg-508.lua

DOWNLOAD

Plugin provided summary

Janitza UMG-508-RM

Values are read as per UMG-96 compatible, but probing is different. Reads firmware version, serial number and model number. Tested against fw version 4.051.

janitza_umg-96.lua

DOWNLOAD

Plugin provided summary

Janitza UMG-96-RM

(and probably UMG-96-S, UMG 511, UMG 605, and all comatible, but not tested yet)

This plugin can read the serial number of a device, but Janitza gives no way of reading the model name that I can decode yet. register 751 contains a HW rev, which, combined with the serial number, may indicate the device type? Janitza's own GridVis software doesn't autodetect the device type either though, you must select the device type _first_ and then it reads the model variant (via register 25010 which contains the modules installed)

Wiring

EG pinMeter pin
+Not connected
-Not connected
AB
BA

papouch-tqs3.lua

DOWNLOAD

Plugin provided summary

Read temperature from a Papouch TQS3 device.

Wiring

EGExtension CableDUT
+REDOrange Terminal Block "+"
-BLACKBlue Terminal Block "-"
AYELLOWGrey Terminal Block "Tx+"
BGREENGrey Terminal Block "Tx-"

rayleigh-instruments.lua

DOWNLOAD

Plugin provided summary

Rayleigh Instruments meters. Tested with RI-D140, and some work with a RI-F385 Product number cannot at this time be identified.

Serial number

Serial number for these devices is in different locations, and must be configured manually until we hear more from Rayleigh Instruments. >
DeviceSerial Register
F10030684
F30030684
F384/F38530684
F40030684
D14030132
MRJ4M30132

Wiring

EGExtension CableDUT
+REDnot connected
-BLACKnot connected
AYELLOW+
BGREEN-

rme-er-kamstrup-351b.lua

DOWNLOAD

Plugin provided summary

Deprecated: Consider using the "etactica_er-generic" plugin instead. Indirect Kamstrup 351b (or compatible) via ReMake Electric ER Requires ER firmware 3.5 or greater.

rme-er-kamstrup-351b.x150.lua

DOWNLOAD

Plugin provided summary

Deprecated: Consider using the "etactica_er-generic" plugin instead. Indirect Kamstrup 351b (or compatible) via ReMake Electric ER Requires ER firmware 3.5 or greater. Preconfigured to multiply readings by 150!

rme-er-kamstrup-351b.x300.lua

DOWNLOAD

Plugin provided summary

Deprecated: Consider using the "etactica_er-generic" plugin instead. Indirect Kamstrup 351b (or compatible) via ReMake Electric ER Requires ER firmware 3.5 or greater. Preconfigured to multiply readings by 300!

rme-er-kamstrup-351b.x40.lua

DOWNLOAD

Plugin provided summary

Deprecated: Consider using the "etactica_er-generic" plugin instead. Indirect Kamstrup 351b (or compatible) via ReMake Electric ER Requires ER firmware 3.5 or greater. Preconfigured to multiply readings by 40!

rme-er-kamstrup-mc-water.lua

DOWNLOAD

Plugin provided summary

Deprecated: Consider using the "etactica_er-generic" plugin instead. Indirect Kamstrup MC (or compatible) via ReMake Electric ER Requires ER firmware 3.5 or greater.

rme-er-legacy.lua

DOWNLOAD

Plugin provided summary

LEGACY - do not use unless you are _very_ sure of what you're doing. This plugin supports the ER09 hardware, with firmware < 3.5 only, of which only a handful of prototype devices were made.

rme-er-pulse-only.lua

DOWNLOAD

Plugin provided summary

Deprecated: Consider using the "etactica_er-generic" plugin instead. Use an eye in optical+wired pulse count mode _only_ Requires ER firmware 3.5 or greater.

rme-er-pulse-w1-only.lua

DOWNLOAD

Plugin provided summary

Deprecated: Consider using the "etactica_er-generic" plugin instead. Use an eye as pulse count wire1 _only_ Requires ER firmware 3.6 or greater.

saia-burgess-Axx3D5x.lua

DOWNLOAD

Plugin provided summary

Saia-PCD 3 phase energy meters from Saia-Burgess with Modbus support

Tested with ALE3D5FD and AWD3D5WD (direct and CT connected) Note: these meters do not support reactive power

Wiring

EG pinMeter pin
+Not connected
-Not connected
A/D
BD
ReMake Electric, 5/2014

saia-burgess-PCD7-H104D.lua

DOWNLOAD

Plugin provided summary

Read pulses from a Saia Burgess PCD7.H104D device.

This supports 4 pulse counts. The programmable multipliers and assignable serial numbers are not presently used.

schneider_electric_a9mem3xx.lua

DOWNLOAD

Plugin provided summary

Schneider Electric Acti 9 iEM3xxx devices.

Developed with an iem3150.

Wiring

EG pinMeter pin
+Not connected
-Not connected
AD1/+
BD0/-

schneider_electric_pm7xx.lua

DOWNLOAD

Plugin provided summary

Schneider Electric Plugin for PowerLogic PM700 series with rs485 support

Currently supports PM710 and PM750 All optional fields are filled.

ReMake Electric, 11/2013.

Wiring

EGExtension CableDUT
+REDnot connected
-BLACKGND
AYELLOWA
BGREENB

siemens_sentron.lua

DOWNLOAD

Plugin provided summary

Siemens Sentron 7KM devices (PAC4200 and PAC3200)

Wiring

In normal mode, the Sentron is a modbus TCP slave, listening on port 502. (on it's ethernet port) With the rs485 module inserted, ensure to configure it as "Modbus RTU".
EG pinMeter pin
+Not connected
-COM
A+/B
B-/A
ReMake Electric, October 2014

smartprocess-smartrail-x835.lua

DOWNLOAD

Plugin provided summary

Smart Process - Smartrail X835

Presumably works for Smartpanel x835 as well, but no modbus document available. Should mostly work for Smartrail x100 single phase meters, but difficult to tell without a sample. (There's no explicit register for model detection, even if the register map appears to be a subset)

Tested with a Smartrail x835MID 2016v2.0, software 1.1.03

Wiring

EGExtension CableDUT
+REDnot connected
-BLACKGND
AYELLOWA
BGREENB

socomec_diris.lua

DOWNLOAD

Plugin provided summary

Socomec Diris A meters.

This is for the "new" Diris family. Old devices with a silver bezel need a different plugin, or work on detection in this plugin. Registers are derived from excel files delivered from Socomec, after pointing out that Socomec document "JBUS Common Table version : 1.01" wasn't correct for currently shipping models. (as of August 2013)

Wiring

EG pinMeter pin
+Not connected
-0
A+
B-